January 30, 2018, 7:36 pm
@L1t7l3ph0o7 wrote:
I'd like to make a cue stack with timing that runs on top of any other chases then releases without releasing the other chases.
for example:
I want to create multiple ques in a stack and record it to one of the user programmable buttons on the m-touch, then when I press that button I want it to cycle through the ques in the stack and then release. I also don't want any other chases to release when I press the button(kind of like an override).
Any Idea on how to accomplish this?
Posts: 2
Participants: 2
Read full topic
↧
January 31, 2018, 2:12 am
@GaryE wrote:
Hello, newbie here. Our College recently purchased and installed a few Zoom PAR 2 lights. I have a couple of questions which hopefully some kind soul can answer:
I have the Rush Uploader1 device for software/firmware updates. The PAR 2 user manual seems to suggest this is compatible, but the Martin support site page for the Uploader doesn't include PAR 2s in the 'must read' pdf of supported fixtures. So does the Uploader 1 support the PAR 2s or not? And is there a device that definitely will do software/firmware updates? Thanks in advance!
Posts: 1
Participants: 1
Read full topic
↧
↧
January 31, 2018, 3:12 am
@Anthrolight wrote:
Hi,
I have a MIDI hardware question and wondering how to go about this.
I have a fully cuestacked show programmed on M-PC, and the band are looking to control it via timecode in case I am not available for some shows.
I've looked into the M-Sync but wanted to look at other options before spending more money.
Basically some backing tracks and a clicktrack are being run from Cubase on another laptop triggered by the drummer, and that can output Midi Timecode.
What hardware would I need to get cubase to send MTC between the two laptops to M-PC, and how would I go about it? I'm not sure what I would need as it not coming from the same laptop.
Cheers,
Alec
Posts: 1
Participants: 1
Read full topic
↧
January 31, 2018, 7:32 am
↧
January 31, 2018, 11:11 am
@jacob.means wrote:
I have been trying to get this to work for quite a while now. I have the firmware I need to update my M-Touch but when I open up the settings, and tap on the firmware for M-Touch, the popup saying services are being stopped displays, then only a moment later, another popup saying that services are being started followed by the popup saying that I need to update the firmware. it doesn't matter if i load the console in bootloader mode or not. please help
Posts: 1
Participants: 1
Read full topic
↧
↧
January 31, 2018, 11:39 am
@GarrettSAFMC wrote:
I have circled certain controls in these photos and included an overall view of my Maxxyz Compact. I've had this in my facility for almost a year now, and I've learned so much. HOWEVER it doesn't seem that certain controls do anything. A couple will appear in the command engine at the bottom of the screen but I can't combine anything with them to create a full command, so I'm not sure what they're for. I also thought maybe the extra belts were just spares, but when we opened it up to dust it out, it's clear those belts are plugged in, so they must do something, right? The arrows don't appear to do anything, CV, Mode, View, and Swap Program don't seem to do anything either. Does anybody know what kind of functionality I can use these for? And how? I want to be able to do everything this console will allow, especially if these buttons are shortcuts.
Posts: 1
Participants: 1
Read full topic
↧
January 31, 2018, 12:07 pm
@Niklas wrote:
Hey,
I don't get a Signal out of my DMX Controller.
I'Ve already tried different PCs, different Interfaces, Cables, etc...
I've also already run the mpc cleaner and reinstalled everthing, but it is still not working.
Thanks for xour help!
Posts: 3
Participants: 3
Read full topic
↧
February 1, 2018, 5:34 am
@sherianderson wrote:
Is this possible? I see a lot of doing it with MPC, but does anyone know if it can connect directly to M2GO?
Posts: 1
Participants: 1
Read full topic
↧
February 1, 2018, 9:12 am
@gears009 wrote:
Up for sale is a Martin Pro Lighting M2PC like new in box, it Just used for programming a show. Works great and its like new in box.
Asking for $1500
Pm me if interested.
Posts: 1
Participants: 1
Read full topic
↧
↧
February 1, 2018, 2:17 pm
@servox wrote:
Hi All
I have a Martin 2510 Controller and x4 SCX600 Scanners
Martin release some pre programmed shows created in lightjockey that are no longer on there website.
I'm hoping that someone has a backup of these files and could help me out and share/email me them.
the programmed shows where called
Funky Electronica
Giga
Mega Party
Electonica
Funky
thank you David
Posts: 1
Participants: 1
Read full topic
↧
February 1, 2018, 2:28 pm
@Ofer_Brum wrote:
Hello Everyone,
It's been a rough month, for M-PC users, but fortunately Microsoft has finally provided a fix to that update which was blocking M-PC outputs! Please update your PC stations, with the latest Windows Update files (KB build varies, according to Windows version & build)
Posts: 2
Participants: 1
Read full topic
↧
February 1, 2018, 3:27 pm
@Wade_Allan_Ratliff wrote:
Hello friends. I am looking to upgrade the hardware in my M1.
The goal is more RAM and faster processing and more cooling.
I will be replacing all the fans and adding liquid cooling (hopefully, that's my last priority) but i would like to upgrade the processor and RAM.
Anyone done this? Got any suggestions on what to upgrade to for best performance?
Thanks a lot guys.
Posts: 1
Participants: 1
Read full topic
↧
February 1, 2018, 8:59 pm
@Andrey wrote:
Good afternoon. I use the M-PC on the laptop. Recently I bought lightjokey 2 and M-Tuch. The program recognized both of them but devices do not see the signal. If you run Console Tester, the devices go crazy. In the program lignjokeyi 2, they respond more or less to tasks. How to make them work in an M-PC?
Posts: 3
Participants: 3
Read full topic
↧
↧
February 2, 2018, 9:39 am
@nickTO416 wrote:
Im getting this error on my new install 3.7 when I do the martin cleaner program whats going here.
I have done all that you ask in this msgs and still nothing
"""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""
Ofer_Brum
This indicates a driver mishmash, as Jungo drivers are no longer used, with 3.70..
Disconnect any Martin USB device
Restart PC
Use MPC Cleaner, to remove M-PC (http://forum.martin.com/t/martin-cleanup-tool/41 )
Run Windows Update, until no pending updates shows up
Restart and reinstall M-PC
Launch M-PC
Reconnect USB device
If still having issues, please move this conversation, to a dedicated post, as it is not relevant to this post
"""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""
Here is the funny part I have install 3.6 then with out uninstalling 3.6 I install 3.7 and it works but I can not get Mplay to work on the 3.7 system. But mplay work on 3.6. and not 3.7 what do you make of that.
As well I can see the mplay in 3.7 when I do the console tester. But can not see the DMX out put of the Mplay.
The other thing I have found in the computer device Manager the when i plug in the mplay it shows up in jungo connectivity as martin M-play but as well it show up in as a unknown usb device here is a pic of it
*************I have spent over 8h trying all the different thing you guys tell me to do so what do I do now******************
Posts: 1
Participants: 1
Read full topic
↧
February 2, 2018, 1:37 pm
↧
February 3, 2018, 8:01 am
@Guix wrote:
Hello everyone,
Today I restore a cuelist that I had put in archive.
The cuelist is totally corrupt, all the dmx data, preset seem to have been mixed...
Anyone already experienced the same issue?...
Thanks.
Posts: 1
Participants: 1
Read full topic
↧
February 4, 2018, 9:29 am
@GarrettSAFMC wrote:
Hoping to find some parts here.... anybody know where I can get these for a Max.xyz Compact? Monitor mounts and the lcd buttons![]()
Posts: 1
Participants: 1
Read full topic
↧
↧
February 4, 2018, 5:44 pm
@Daniel_Morris wrote:
This is a fairly simple suggestion but I think it would be pretty neat to have.
other brands have it. But I was wondering if it would be possible to add a feature where you can have a graphic as your console lock screen so if you're on a tour or something when you lock your console you can have it display the band graphic. Or your company graphic.
Thanks!
Posts: 1
Participants: 1
Read full topic
↧
February 5, 2018, 2:23 am
@Betabell wrote:
Hi
We've been using LightJockey 2 and all the most important sequences are mapped to hotkeys on computer keyboard so we can trigger them very quickly.
I'm exploring the M-PC and I'm wondering is it possible to use computer keyboard for triggering cuelists/chases with M-PC. For an example I want to map key"C" for triggering moving heads chase and "S" triggers strobe.
Thanks.
Posts: 2
Participants: 2
Read full topic
↧
February 5, 2018, 9:50 am
@SoundSolutionDJ wrote:
I'm looking for the Profile of the American DJ Pocket Crazy 8 and can't seem to find it anywhere.
I have downloaded the profiles and the update pages and searched for the fixture here to no avail.
I'm brand new here.
Thanks
Dave
Posts: 3
Participants: 3
Read full topic
↧
